How To Repair Macbook Air Charger

Introduction

Sometimes the cable starts peeling simply at that identify where it meets the Air conditioning Adapter. I've met besides many people that throw away their chargers because of this. It takes time and patience but repair is possible!

• Nasty cut.



• Unplug your AC ability string.

• Expect at the line that goes though the charger. This is all glued with some super adhesive that prevents you from merely taking it autonomously.

• You will accept to cutting through that plastic, go all the way effectually post-obit that small space with your knife.

• This will take a while, you lot take to cutting the plastic from all the 4 sides. You will observe when you take cut through nearly of information technology.

• Be conscientious with the side shown in the last picture. At that place are a couple of components that might be cutting in the process.

• With a flat headed screwdriver start separating both plastic faces from the charger. Y'all need to utilize a piffling forcefulness to practice this.

• Once you lot accept separated all sides with the spiral driver, it still wont come off. This thing is glued to all sides of the plastic.

• Insert the screwdriver into the peak part of the charger and carefully divide the foil from the plastic enclosure. Be careful as to not rip off the foil from the inner part of the charger.

• In this step I already took off one face of the plastic enclosure.

• Use the screwdriver to loosen upwards the adhesive on both sides of the power connector.

• Insert the screwdriver on the remaining confront of the plastic enclosure and advisedly loosen upward the rest of the adhesive.

• You lot should end up with this block. Put abroad the plastic enclosure.

• Grab the small plastic piece that attaches the cables to the AC charger.

• Cut the cables every bit near as y'all can to the plastic piece.

• Peel the plastic off the cablevision with a knife or a wire stripper.

• Take the cable that connects to your mac book and advisedly skin it off with a knife or a wire stripper.

• Untangle the outer wire to reveal the white cable inside.

• Twirl up nicely the outer wire and peel a pocket-sized bit of the white cablevision to bring together the to the Ac charger.

• Join both white cable wires and solder them together.

• Retrieve that the white wire from the Air conditioning adapter NEEDS to be soldered to the white wire from the cable that comes from the MacBook connector.

• The black insulated embrace tube on the cable is to isolate the cable later, you can utilise heat to shrink it.

• The concluding pic shows the blackness insulated cover tube, you tin can cut it up to fit the length you need.

• It is very important to isolate both wires, they cannot touch each other or else they volition short circuit (in other words: Kaboom!).

• Go on to solder the blackness cablevision from the Air-conditioning charger to the outer wire of your Macbook connector.

• Isolate that wire. You don't need to comprehend upwardly the whole extension of the outer wire, just enough so that it won't bear on the white cable or the excursion lath of the AC adapter.

• You can use the black rubber tube or electric tape. If you lot use the black tube try to go along it as far away equally possible when soldering to prevent it from shrinking earlier y'all cover the wire.

• Cover up with electrical tape the remainder the white and black/outer cable you just soldered.

• Bring together them together with electrical tape as to form one cable and place the Ac charger in one of the faces of the plastic enclosure.

• White electrical record makes this fix look nicer.

• Take 3 small cipher ties and tie them around the cable to stop information technology from existence pulled out of the plastic enclosure.

• Put pocket-size bits of super glue on the borders of the enclosures. Place the other face of the plastic enclosure and close upwardly the Ac charger.

• Don't forget the plastic tabs that let you lot wrap your cable on the charger... Even though those are the primary cause for your cable fierce up! I usually choose to leave them out or glue them to the enclosure to forestall the cablevision breaking once again.

• Necktie four large zip ties to close up the enclosure, 2 on each side.

• Some people prefer to utilize only super glue because it looks nicer but zilch ties make it safer. If you lot like it ameliorate without the nada ties, accept them out afterward a few hours afterward the super glue has bonded completely.

• Apply a gum gun to shut upward the gap that remains.

• Don't use too much, just plenty then that in that location is no opening from the outside.

Embed this guide

Cull a size and copy the code beneath to embed this guide as a modest widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/How+to+Repair+an+Apple+AC+Adapter+Broken+Cable/20434

Posted by: smithpule1960.blogspot.com

Share this post